Coffein

Caffeine

CAS 58-08-2  ·  C8H10N4O2  ·  MW 194.19 g/mol

Coffein (CAS 58-08-2) — full MolGod record →
Safety data sheet with all sections: GHS classification, transport, regulatory status, spectra, 3D model and literature.
Molekül wird geladen...
3D-Modell Caffeine, CAS 58-08-2, Summenformel C8H10N4O2, molare Masse 194.19 g/mol

Modellansichten

  • Coffein (CAS 58-08-2) – 3D-Kugel-Stab-Modell, MolGod Viewer
    3D-Kugel-Stab-Modell
  • Coffein (CAS 58-08-2) – 3D-Skelettmodell, MolGod Viewer
    3D-Skelettmodell
  • 3D-Kalottenmodell – Rotationsanimation
  • Coffein (CAS 58-08-2) – 2D-Struktur, MolGod Viewer
    2D-Struktur

© 2026 MolGod.org. Alle Rechte vorbehalten. · Bildrechte

🖨️ 3D-Druckmodell und LizenzMolGod_Print3D_1

Ein druckfertiges Modell dieses Moleküls auf einem Sockel: drehen, heranzoomen und ansehen, wie es direkt aus dem Drucker und nach dem Entfernen der Stützen aussieht.

Preview of the 6-colour print model — rotate it with your mouse or finger; see it as printed, finished, as the molecule alone, and where to cut it off the pencils

Loading the 3D model…

Drag to rotate; scroll or pinch to zoom. Each part is shown in the colour of its filament.

6 colours in one print, no paintingBambu Lab H2C, 0.4 mm nozzle, 0.16 mm layersabout 172 g of PLAabout 16 h 46 min of printing (slicer estimate)Slicer-tested, multicolour test print still to come

⬇️ Sliced for H2C (G-code 3MF) · 48 MB⬇️ Everything in one ZIP · 148 MBFull multicolour specification ↓

caffeine (CAS 58-08-2), C8H10N4O2 - 3D ball-and-stick molecular model, engraved element symbols (C H N O), MolGod STL previewBild herunterladen

MG_751-125-824-41 · engraved · 305,524 △ · 15 MB · SHA-256 3eca6dd62995ddf8

3D-Modell herunterladen: Caffeine, C8H10N4O2, CAS 58-08-2 · ENGRAVED (C, H, N, O) · 15 MB

caffeine (CAS 58-08-2) - 3D model ready to print on a display base, MolGod STL previewBild herunterladen

MG_751-125-824-41 · ready to print · ANT HOUSE v7 · 450,102 △ · 21 MB · SHA-256 61bbb8ec736087db

Digital geometry validated. Slicer-tested with the stated profile. Physical print not yet tested.

Druckgröße in Millimetern: mit 100 % importieren, nicht skalieren.

3D-Druckeinstellungen · ANT HOUSE v7 — digitale Geometrie validiert; Slicing mit dem unten angegebenen Profil (PrusaSlicer 2.8.1 · ANT HOUSE profile v4 (in the 3MF)) für genau diese Datei geprüft; noch kein physischer Druck durchgeführt.
Dateimolgod_caffeine_58-08-2_R3-ready-to-print_g2026-10-28_NO-SUPPORTS_add-supports-in-slicer.stl · ANT HOUSE v7
SHA-256 61bbb8ec736087dbfad3fb423807465294afff81c257254bf4b07e0728b97f0b
Geslict am 2026-10-28 (UTC) für diesen SHA-256
ReifegradStufe 3 von 5 — Slicer-verifiziert (1 Generiert · 2 Geometrie validiert · 3 Slicer-verifiziert · 4 Physisch gedruckt · 5 Druckqualifiziert). Für den FDM-Druck konzipiert. Geometrie validiert, Slicing mit dem angegebenen Profil geprüft. Ein physischer Druck wurde noch nicht durchgeführt.
MethodeFDM, PLA 1.75 mm
Düse0.4 mm (die kleinsten Details sind für diese Düse ausgelegt; keine größere verwenden)
Schichthöhe0.2 mm
Füllung15%, 3 Perimeter
StützstrukturenJa. 11 Bleistiftstützen (Ø 3.5 / 5 mm, sechseckig, Graphithals Ø 1.8 mm mit 45°-Kelch unter dem Atom, 10.0–41.3 mm lang) sind Teil des Modells — nicht entfernen. Aktivieren Sie zusätzlich die automatischen Stützstrukturen des Slicers: Sie sind temporär (ca. 25.2 % des Druckvolumens in unserem Durchlauf) — entfernen Sie sie vorsichtig an den kleinsten Kugeln (z. B. Wasserstoff) und dünnen Bindungen. In Ihrem eigenen Slicer: organische (Baum-)Stützen mit ausgeschaltetem „nur auf dem Druckbett“ (on build plate only) — jeder Baum beginnt auf der Basis (Cura: Support Placement = Everywhere). Drücken Sie nach der Wahl Ihres Druckers A (Anordnen), damit das Modell in der Mitte des Druckbetts steht.
Temperatur3MF-Profil: 215 °C Düse in der ersten Schicht, danach 210 °C; Bett 60 °C (Ausgangswert — halten Sie sich an den Bereich des Filamentherstellers); Bauteillüfter ab Schicht 4. Die fertigen G-Codes nutzen die Temperaturen und Lüftereinstellungen der Druckerhersteller (Liste: gcode/README_GCODE.txt im Paket). Fertiger G-Code (Prusa MK4, Prusa MINI, Creality Ender-3 S1): Düse 210 °C in der 1. Schicht, danach 205 °C; Bett 60 °C — Werte aus dem Kopf jeder Datei.
AusrichtungWie geliefert drucken: Sockel flach auf dem Druckbett (Seite mit QR-Code nach unten); nicht drehen
MaßstabMit 100 % importieren — die Datei ist in Millimetern; nicht skalieren (Molekülmaßstab 1 Å = 10.60 mm)
Gesamtabmessungen100.0 × 100.0 × 84.1 mm (X × Y × Z); Sockel Ø 100 × 20 mm
Validiert2026-10-28 (UTC): Geometrieprüfungen dieser Datei
Mindestgröße Druckbett125 × 125 mm; Höhe 90 mm
Geschätzte Druckzeitetwa 9 h 52 min (3MF-Profil in PrusaSlicer; Zeiten der fertigen G-Codes oben)
Filament (PLA)ca. 85–87 g (Slicer-Schätzung)

So wird dieses Modell gedruckt

caffeine (CAS 58-08-2) direkt aus dem Drucker: orangefarbene Slicer-Stützen, gelbe Bleistift-Stützen
Direkt aus dem Drucker: die orangefarbenen Slicer-Stützen entfernen, die gelben Bleistifte bleiben
caffeine (CAS 58-08-2) fertiges Modell nach Entfernen der Slicer-Stützen
Fertiges Modell: weißes Molekül auf gelben Bleistiften, erhabenes MolGod-Logo

Renderings (PNG):

caffeine (CAS 58-08-2) druckfertiges 3D-Modell, Vorderansicht, gerendert aus der MolGod-STL-Datei
Vorderansicht
caffeine (CAS 58-08-2) druckfertiges 3D-Modell, Seitenansicht, gerendert aus der MolGod-STL-Datei
Seitenansicht
caffeine (CAS 58-08-2) druckfertiges 3D-Modell, 3/4-Ansicht, gerendert aus der MolGod-STL-Datei
3/4-Ansicht
caffeine (CAS 58-08-2) druckfertiges 3D-Modell, Draufsicht, gerendert aus der MolGod-STL-Datei
Draufsicht
caffeine (CAS 58-08-2) druckfertiges 3D-Modell, Unterseite, gerendert aus der MolGod-STL-Datei
Unterseite

Für Druckdienstleister:
Technisches Datenblatt (PDF: Zeichnung, Abmessungen, Druckspezifikation) · 588 KB · SHA-256 4161deaafa039710…
Druckpaket (ZIP: STL, 3MF mit Einstellungen, G-Code, Schritt-für-Schritt-Anleitung, Konstruktionsnotizen mit Quellen, Bild „was entfernen“, Vorschauen, Slicer-Profil, Prüfbericht, QC-Checkliste, Rückmeldeformular, Lizenz) · 55 MB · SHA-256 8ad0b62d8de8af97…

3D-Modell herunterladen: Caffeine, C8H10N4O2, CAS 58-08-2 · READY TO PRINT · STL ohne Stützen · 21 MB · base Ø 100 mm · single integrated solid

Caffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, front three-quarter view
Caffeine (CAS 58-08-2) READY TO PRINT MULTICOLOR release r7 as printed: render with the slicer supports (orange) taken from the sliced G-code, all standing on the baseCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, top viewCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, side viewCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, low front viewCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, back viewCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, close-up of the scissor cup under an oxygen atomCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, close-up of the raised CAFFEINE / CAS 58-08-2 labelCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, close-up of the raised formula C8H10N4O2Caffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, bottom view with the engraved QR codeCaffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR: 30 render views from every side, top and bottom

Pictures above are renders of the print model, not photos (the second one shows release r7 as printed, with its supports). The multicolour version has not been printed yet; photos of our single-colour print are in the tab SEE PRINTED 3D MODELS.

  • For Bambu Lab H2C
  • 6 colours, one print
  • 0.4 mm nozzle · 0.16 mm layers
  • 988 filament changes
  • about 16 h 46 min
  • about 172 g of PLA

Made for one printer

This project is set up for the Bambu Lab H2C and is not a universal multicolour file. Using another multicolour printer? The ZIP contains the six STL files, one per colour, for manual material assignment. Slicing and validation for your printer are then up to you: we have not tested other printers.

What you get

The same caffeine molecule and pencil pillars as READY TO PRINT, in colour straight off the printer: atoms labelled with their element symbols, red pencils with gold sharpened wood, and a white base with the blue MolGod.org logo, the raised formula C8H10N4O2 and a raised CAFFEINE / CAS 58-08-2 label.

Atom colours follow the chemistry convention

Every atom carries its element symbol and is coloured according to the CPK convention used for molecular models in chemistry: carbon black, hydrogen white, nitrogen blue, oxygen red. The name CPK comes from the Corey–Pauling–Koltun space-filling models described below. Single bonds are white. A double bond to oxygen or nitrogen takes that atom's colour, red C=O and blue C=N, so the double bonds stand out; the C=C double bond stays white.

Where the name CPK comes from

Where the geometry comes from

Atom positions come from the 3D conformer of caffeine computed by PubChem (CID 2519) with the OMEGA conformer generator. It is a computed structure, not an experimental crystal structure. The MolGod engine (R3, recipe r3-1.3) scales it to 10.598 mm per ångström, orients it for printing and places it on the base with its own pencil supports.

Sources for the 3D structure

  • Bolton, Evan E., Jie Chen, Sunghwan Kim, Lianyi Han, Siqian He, Wenyao Shi, Vahan Simonyan, Yan Sun, et al. 2011. "PubChem3D: A New Resource for Scientists." Journal of Cheminformatics 3: 32. https://doi.org/10.1186/1758-2946-3-32
  • Hawkins, Paul C. D., A. Geoffrey Skillman, Gregory L. Warren, Benjamin A. Ellingson, and Matthew T. Stahl. 2010. "Conformer Generation with OMEGA: Algorithm and Validation Using High Quality Structures from the Protein Databank and Cambridge Structural Database." Journal of Chemical Information and Modeling 50 (4): 572–584. https://doi.org/10.1021/ci100031x

Which file do I need?

To print exactly what we checked, use the sliced 3MF: it carries our printer, filament and support settings and the G-code for the H2C. The project 3MF of release r7 is the same project without G-code and keeps all those settings, so you can adjust it and slice again. The ZIP adds the six STL files and the renders.

Print settings

Nozzle 0.4 mm on every nozzle, layer 0.16 mm, Bambu PLA Basic in six colours. Supports: regular, snug style, threshold 44°, with "remove small overhangs" switched off so the slicer also supports the tiny undersides of the hydrogen atoms; 3 support enforcers and a support blocker ring at the bottom edge of the base are part of the project. All supports stand on the base or on the model, none on the build plate. Bambu Studio assigns white to the first extruder and the other five colours to the second, which switches hotends; the G-code contains 988 filament changes. Bambu Studio estimates 16 h 46 min and 172 g; your printer and settings may differ.

Cutting the molecule off the pencils

The pencils hold the molecule during printing and can stay as a display stand. If you want the molecule on its own, each pencil ends in a small cone under the atom, the scissor cup, printed in the colour of that atom:

  1. Remove the slicer's tree supports first. The red pencils are part of the model and stay.
  2. Cut with flush cutters straight across the black graphite where it meets the cup. The cross-section there is about 2 mm.
  3. Cut one pencil at a time and do not twist or pull the molecule: the bonds are thin.
  4. The cut face stays in the colour of the atom. Smooth a small stub with fine sandpaper if you like.
Caffeine (CAS 58-08-2) - READY TO PRINT MULTICOLOR, 6-colour Bambu Lab H2C print model, MolGod 3D render, close-up of the scissor cup under an oxygen atom
Render: the scissor cup under an oxygen atom, in the atom's colour, at the tip of the pencil graphite. Not yet tried on a physical multicolour print.

Supports: what changed in r7

Release r6 used tree supports and left 10 tiny spots (0.6 to 1.4 mm²) on the outer surface unsupported, mostly under hydrogen atoms: every tree setting that reached them went down to the build plate. Release r7 uses straight snug supports, which grow down onto the base, and supports the undersides of all hydrogen atoms: 0 unsupported spots on the outer surface. Our detector still raises one flag (0.74 mm²), but it lies 1.2 mm inside a hydrogen atom: the bottom layer of the black letter laid on the white infill inside the ball, which needs no support. The price of r7: about 36 minutes and 10 g more than r6, and more support to remove between the pencils.

Caffeine (CAS 58-08-2) READY TO PRINT MULTICOLOR release r7 as printed: render with the slicer supports (orange) taken from the sliced G-code, all standing on the base
Render of release r7 as printed: supports (orange) from the sliced G-code, all on the base.

Using it in class

The model can help pupils recognise atoms by colour and symbol, tell single from double bonds, compare the flat 2D formula on the base with the 3D shape, and see the two fused rings and three methyl groups of caffeine. We have not run classroom studies yet; teachers who try it are welcome to write to pure@molgod.org.

Filaments: six colours, one per nozzle (the 7th nozzle stays free)

  • Jade White 10100 · 96.5 gbase, hydrogen atoms, single bonds and the C=C bond, letters on C, N and O
  • Black 10101 · 17.5 gcarbon atoms, pencil graphite, letters on H, text and QR code on the underside
  • Blue 10601 · 15.2 gnitrogen atoms, C=N bonds, logo, CAFFEINE, CAS number, formula
  • Red 10200 · 22.6 goxygen atoms, C=O bonds, pencil bodies
  • Light Gray 10104 · 4.5 gmetal ferrules on the long pencils
  • Gold · 16.1 gsharpened wood and erasers

Downloads

Current multicolour release: r7 (1 November 2026), checked digitally and in the slicer; a physical multicolour test print is still pending. Release r6 stays available below. The pictures on this tab are renders.

Quality passport · release r7 · 1 November 2026

What we checked for this multicolour release, what the result was and what it is based on. A higher step is never assumed from a lower one.

  • PASSChemical identityCAS 58-08-2, C8H10N4O2, InChIKey RYYVLZVUVIJVGH-UHFFFAOYSA-N, PubChem CID 2519. The model has 24 atoms, matching the formula (8 C, 10 H, 4 N, 2 O), each with its element letter.
  • PASSGeometry and meshOne watertight solid, 434,520 triangles. Inside the solid, the colour parts match its volume (139,258 mm³) to within 0.000001 %; the published STL files add 574 mm³ more, mostly the filled lettering and QR code recessed in the underside of the base. 25 bonds (29 bond cylinders, the four double bonds are drawn double), 13 pencils.
  • PASSSlicer check (Bambu Studio 02.08.02.61, H2C)Sliced without errors; no supports on the build plate; 0 unsupported spots on the outer surface (r6: 10). The detector's single flag lies 1.2 mm inside a hydrogen atom (letter layer on infill); the depth check that separates the two was validated on the 10 r6 spots, all found on the surface. The project file re-sliced on its own gives the same result.
  • PASSReproducibility of the colour splitSplitting the same solid into colours again produced all 17 colour parts byte-for-byte identical (31 Oct 2026). A full rebuild from the recipe has not been tested yet. SHA-256 of each download is listed on its card above.
  • PENDINGPhysical multicolour printNot printed yet. The photos in SEE PRINTED 3D MODELS show the single-colour READY TO PRINT version, not this one.

Level 3 of 5 — Slicer Verified (1 Generated · 2 Geometry Validated · 3 Slicer Verified · 4 Physically Printed · 5 Print Qualified). Designed for FDM printing. Geometry validated and slicing checked using the specified profile. No physical print has been made yet.

Release r7: digital geometry checked; sliced and checked in Bambu Studio 02.08.02.61 on the Bambu Lab H2C profile. Physical multicolour print: pending.

Licence of this print model: CC BY-NC-SA 4.0 International (non-commercial) - https://creativecommons.org/licenses/by-nc-sa/4.0/

Caffeine molecule 3D printed on a Bambu Lab printer, side view: ball-and-stick model with element letters on a MolGod.org base (CAS 58-08-2, C8H10N4O2)
Caffeine molecule 3D printed on a Bambu Lab printer, side view: ball-and-stick model with element letters on a MolGod.org base (CAS 58-08-2, C8H10N4O2)
Top view of the 3D printed caffeine model: purine rings, three methyl groups and the engraved MolGod.org base with the formula C8H10N4O2
Top view of the 3D printed caffeine model: purine rings, three methyl groups and the engraved MolGod.org base with the formula C8H10N4O2
Close-up of the white 3D printed caffeine desk model (ball-and-stick, pencil pillars, labelled base), CAS 58-08-2
Close-up of the white 3D printed caffeine desk model (ball-and-stick, pencil pillars, labelled base), CAS 58-08-2

Real photos of our own print of this model, made from the ready-to-print release (r19) offered on this page: printed in one piece on a Bambu Lab 3D printer in single-colour white filament, pencil pillars left in place, unpainted.

Photographed on 30 October 2026. Printed it yourself? Send us a photo: pure@molgod.org.

caffeine (CAS 58-08-2), C8H10N4O2 - 3D ball-and-stick molecular model, MolGod STL previewBild herunterladen

MG_751-125-824-41 · normal · 10,464 △ · 511 KB · SHA-256 9aa8d8a1e01adc89

3D-Modell herunterladen: Caffeine, C8H10N4O2, CAS 58-08-2 · NORMAL · 511 KB

Lizenz und Provenienz ↓

⚠️ Logo und Name MolGod.org, einschließlich des erhabenen Logos auf dem Sockel, sind unsere Marke. Creative-Commons-Lizenzen umfassen keine Marken (§ 2(b)(2)). Ohne unsere schriftliche Zustimmung dürfen Sie das MolGod.org-Logo nicht zur Kennzeichnung eigener Produkte, in der Werbung oder in einer Weise verwenden, die unsere Unterstützung nahelegt.

Über Coffein

Coffein ist eine chemische Verbindung, registriert unter der Nummer CAS 58-08-2, mit der Summenformel C8H10N4O2, und einer Molmasse von 194.19 g/mol.

Das Molekül enthält 24 Atome, verbunden durch 25 chemische Bindungen. Der vollständige systematische IUPAC-Name dieser Verbindung lautet 1,3,7-trimethylpurine-2,6-dione. Das interaktive 3D-Modell oben zeigt die räumliche Anordnung der Atome — Sie können es mit der Maus drehen, mit dem Scrollrad zoomen und zwischen den Darstellungsmodi Skelett / Ball & Stick / Space Fill wechseln.

Hinsichtlich der physikalisch-chemischen Eigenschaften der Verteilungskoeffizient logP = -0.1 (negativer Wert, hydrophile Verbindung), polare Oberfläche PSA = 58.44 Ų, 0 Donatoren und 6 Wasserstoffbrücken-Akzeptoren. Diese Parameter sind entscheidend für die Beurteilung der Bioverfügbarkeit und der Wechselwirkung mit Biomolekülen.

Die chemischen Daten für diese Verbindung stammen aus PubChem (NIH NLM NCBI), einer der größten chemischen Datenbanken der Welt. Alle Informationen werden automatisch aktualisiert und um GHS-Gefahrenhinweise gemäß der CLP-Verordnung (EG 1272/2008) ergänzt. Das interaktive 3D-Modell und die Bilder des Viewers sind urheberrechtlich geschützt (© MolGod.org) — Nutzungsbedingungen: molgod.org/copyright/.

Physikalisch-chemische Eigenschaften
Molecular formulaC8H10N4O2
Molar mass194.19 g/mol
IUPAC1,3,7-trimethylpurine-2,6-dione
SMILESCn1cnc2c1c(=O)n(c(=O)n2C)C
InChIKeyRYYVLZVUVIJVGH-UHFFFAOYSA-N
logP (XLogP3)-0.1
PSA58.44 Ų
HBD / HBA0 / 6
PubChem CIDCID 2519 ↗
GHS-Sicherheit

Signalwort: Achtung

GHS07
GHS07

H302 — Gesundheitsschädlich bei Verschlucken.

Wissenschaftliche Literatur

Related literature

9 articles · 7 open access · Sources: PubMed, OpenAlex, Semantic Scholar

Filter:Export:📄 BibTeX📑 RIS📋 EndNote🔧 CSL-JSON

📈 Publikationszeitachse (Anzahl der Artikel: 9)

2025: Anzahl der Artikel 620252026: Anzahl der Artikel 32026

Balkenhöhe = Anzahl der Artikel im jeweiligen Jahr. Bewegen Sie den Mauszeiger über einen Balken, um Details anzuzeigen.

Data from PubMed (NIH NLM), OpenAlex (CC0), Semantic Scholar (AI2). AI Summary generated by Semantic Scholar TLDR. Articles marked with require paid access.

Synonyme
Caffeine · 1,3,7-Trimethylxanthine · Guaranine
Datenquellen
Verwandte Moleküle
📜 Lizenz und ProvenienzMolGod_License_1
COMPUTED — PubChem3D · 3D conformer computed by PubChem using OMEGA; not an experimental structure.
Modell
caffeine · 58-08-2
InChIKey
RYYVLZVUVIJVGH-UHFFFAOYSA-N
Lizenz
CC BY-SA 4.0 International
Lizenz des Druckmodells (READY TO PRINT)
CC BY-NC-SA 4.0 International — Modell mit Sockel und Stiften; die Lizenz oben gilt für die Moleküldateien NORMAL und ENGRAVED
Namensnennung
MolGod Scientific — caffeine (CAS 58-08-2)
Lizenz- und Provenienzeintrag
caffeine (CAS 58-08-2) →
MolGod-Moleküleintrag
caffeine →
Quelldaten
PubChem CID 2519 ↗
Modellinformationen
STL erzeugt von MolGod · MolGod STL Exporter build 48804cd20b0d · erzeugt 2026-10-14
SHA-256 (STL)
9aa8d8a1e01adc890f457a9e603129e4da7b8b6296b3a63040914176e7c77ac6
MD5 (STL)
806b0455f4bf87a83a4115f9f8729ed4
MolGod Identification Number
MG_751-125-824-41
Transformation
MolGod Scientific Kugel-Stab-Netz
Änderungen
In ein trianguliertes Molekülnetz umgewandelt; Atomkoordinaten und Konnektivität unverändert.
Wikimedia Commons
noch nicht veröffentlicht
Kostenloses Molekülmodell zum Drucken
Laden Sie das Modell herunter, drucken Sie es aus und nutzen Sie es im Unterricht. Wenn Sie ein Foto, ein Material oder eine Bearbeitung veröffentlichen, verlangt die Lizenz CC BY-SA 4.0 International: „MolGod Scientific“ als Urheber des Modells nennen, auf das Original und den Lizenztext verlinken, vorgenommene Änderungen kenntlich machen und Bearbeitungen unter derselben Lizenz weitergeben. Einen fertigen Namensnennungstext finden Sie in diesem Abschnitt. Ohne Registrierung, ohne Kosten und ohne Pflicht zur Bewertung.
Dieser Hinweis gilt für die Moleküldateien NORMAL und ENGRAVED. Das READY-TO-PRINT-Modell mit Sockel steht unter CC BY-NC-SA 4.0 (nichtkommerzielle Nutzung) — Details im Tab READY TO PRINT. ↑

⚠️ Logo und Name MolGod.org, einschließlich des erhabenen Logos auf dem Sockel, sind unsere Marke. Creative-Commons-Lizenzen umfassen keine Marken (§ 2(b)(2)). Ohne unsere schriftliche Zustimmung dürfen Sie das MolGod.org-Logo nicht zur Kennzeichnung eigener Produkte, in der Werbung oder in einer Weise verwenden, die unsere Unterstützung nahelegt.

Diese Lizenz gilt für das von MolGod erstellte STL-Mesh, nicht automatisch für Quellmaterial Dritter.

—